Body Armor 4×4® – 3rd Brake Light

Description

Product Details3rd Brake Light by Body Armor 4×4®. This extremely rugged swing arm mounts to the right end of the Body Armor rear bumper with a pair of wheel bearings and a wheel spindle, assuring an extremely strong, rattle-free connection. It also mounts a number of other accessories.Product linesVideoAbout usFeaturesConstructed of 3/16” carbon steelTextured black powdercoat finishHigh clearance design to maximize departure anglesMachined spindle-style/bearing pivot shaft for swing arm 5294Dual wheel bearing pivot systemSwing arm can carry 40” tire, Hi-Lift jack, 2 gas cansNo-drill, no-weld simple installPositive latching systemThis is a bumper system that’s truly trail-ready. This rugged, close-fitting rear bumper allows for ample departure angles and improved ground clearance over the stock bumper. Equipped with a pair of welded shackles with D-rings for recovery points, it also retains the factory hitch receiver for a third recovery point if necessary. The pivot point is not a simple pin and bushing, but based on an automotive spindle and a pair of wheel bearings, guaranteeing that the swing arm will be easy to swing, and never start to rattle from the rigors of the trail. Add a gas can kit and a mount for a hi-lift jack knowing that the bumper and swing arm are up to the task of carrying that weight as well as a mounted 40” tire. Body Armor even has a kit to raise the CHMSL up to clear the huge spare tire. Body Armor 4×4® is the newest addition to the Tolar family of products. A major supplier of transit shelters and outdoor advertising displays, Tolar has leveraged its expertise in steel fabrication into making the ruggedest off-roading products on the market. Based in Corona, CA, Body Armor is perched right at the edge of some of the best off-roading sites in the country, giving them access to a tremendous body of knowledge of what works and what doesn’t when you’re miles from the nearest road. Building its business on a commitment to quality products and superior customer service, Body Armor has brought together a unique team of designers, engineering specialists and metal fabrication professionals with over 30 years of experience in the off-road products industry. California Residents WARNING Cancer and Reproductive Harm.   www.p65warnings.ca.gov Have a Question? Ask an Expert833-839-0215 WarrantyBody Armor 4×4 (BA) warrants to the original purchaser that these products will be free from defects in material and workmanship prior to shipping and/or installation for the life of the product. This non-transferable limited lifetime warranty does not cover damage or impairment in any part due to misuse, improper installation, accident or contact with on-road or off-road hazards, product modification, improper or inadequate cleaning and/or maintenance. All other warranties and representations express or implied are hereby disclaimed, including fitness for merchantability and buyer’s intended use or purpose. BA products are built and sold for highway and off-road use. The original purchaser assumes all risks as to the selection, suitability and performance of all goods and products purchased. BA’s sole and exclusive obligation under this warranty shall be to repair or replace the item(s). FINISH WARRANTY The finish is warranted to be free of defects for a period of 3 years from date of purchase. Product(s) that have been abused, altered, incorrectly installed or used in competition are void of said warranty. Surface rust, pitting or discoloration is a direct result of improper maintenance is not covered by this warranty. It is the responsibility of the owner to preserve and maintain the finish of their product(s). In areas where high concentrations of road salts and other corrosive agents are used, rust or damage to the finish may occur if BA product(s) are not properly maintained. Lack of proper maintenance in these areas may void the finish warranty. See below for routine maintenance tips and recommendations. PRODUCT CARE AND MAINTENANCE Textured coat finished should be cleaned ONLY with a mild soup on a damp sponge BA recommends wiping down the product with a light coat of lubricate (i.e. WD40) periodically to maintain its luster DO NOT apply polish or wax that requires buffing for removal as this may damage the finish DO NOT coat the product with any type of shine such as Tire Shire or glossy aerosol or gel. This can cause discoloration, staining or bubbling Magnuson-Moss Warranty Act:Legally, a vehicle manufacturer cannot void the warranty on a vehicle due to an aftermarket part unless they can prove that the aftermarket part caused or contributed to the failure in the vehicle (per the Magnuson Moss Warranty Act (15 U.S.C. 2302(C)) Learn More Related LinksWheels & TiresSpare Tire Covers & CarriersBody Mounted Spare Tire CarriersBody Armor 4×4 Spare Tire Covers & Carriers